Filter By:
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
Tools

$429.95
The BBP-AOS is used in conjunction with the BBP-1.2 Bottom Bracket Bearing Press Kit to extract press fit bottom bracket bearings, cups, and adaptors. The BBP-AOS utilizes an expanding collet and extractor cup system to safely remove bearings without requiring impact. Also included are eight installation drifts for pressing bearings into pre-installed cups.
- 8 precision-machined extractor cups and 5 hardened collets for compatibility with most bearing IDs and bearing/cup ODs
- 8 installation drifts for standalone bearing installation
- Organized in a convenient storage case
- Full list of compatible bearing inner/outer diameters found on instructions/parts diagram
NOTE: The BBP-AOS requires the BBP-1.2 Bottom Bracket Bearing Press Set for use. The BBP-1.2 and BBP-AOS are also available as a complete set (part # BBP-2).

$389.95
The SHX-1 Slide Hammer Extractor is a professional solution specifically designed for removing press fit cartridge bearings from bicycle components. Utilizing expanding collets, an extendable shaft, and a substantial (960g) slide hammer, the SHX-1 securely yet forcefully drives out cartridge bearings with targeted impact. The SHX-1 is compatible with cartridge bearings with inner diameters from 6 to 32 millimeters, covering most press fit applications found on bicycles including hubs, suspension linkages, and bottom brackets.
- Set of 5 expanding collets covers most bicycle bearing IDs from 6mm to 32mm
- Slide hammer shaft is extendable from 6.5" (165mm) to 13" (233mm) for additional force when needed
- Organized in a convenient storage case

$339.95
We put together this set of carefully chosen tools to do basic maintenance and cleaning as well as perform a wide variety of repairs and adjustments on just about any bicycle. A perfect way to start or add to your collection of shop-quality bicycle tools. The AK-5 includes a tough toolbox to protect your investment.
Kit Includes:
- AWS-1 3-Way Hex Wrench
- BBB-4 Big Blue Book of Bicycle Repair
- CC-4 Chain Checker
- CM-5.3 Cyclone Chain Scrubber
- CN-10 Professional Cable and Housing Cutter
- CNW-2 Chainring Nut Wrench
- CT-3.3 Chain Tool
- DCW-1 Double-Ended Cone Wrench: 13/14mm
- DCW-2 Double-Ended Cone Wrench: 15/16mm
- DCW-3 Double-Ended Cone Wrench: 17/18mm
- DH-1 Dummy Hub
- DT-2 Rotor Truing Fork
- FR-5.2 Cassette Lockring Tool
- GSC-1 GearClean Brush
- HCW-16.3 Chain Whip/Pedal Wrench
- HXS-1.2 Professional L-Shaped Hex Wrench Set
- MLP-1.2 Master Link Pliers
- PAW-12 12" Adjustable Wrench
- RR-12 Tape Measure
- SD-2 #2 Phillips Screwdriver
- SD-3 3mm Flat Blade Screwdriver
- SW-0 Precision Spoke Wrench: .127"
- SW-2 Precision Spoke Wrench: .136"
- TL-1.2 Tire Lever Set
- TWS-3 Torx Compatible 3-Way Wrench
- VC-1 Valve Core Tool

$289.95
The SBK-1 is a professional level kit for installing and removing cartridge bearings in bicycle suspension pivots. A comprehensive set of 27 precision-machined hard-anodized guides enables compatibility with a wide range of bearing inner and outer diameters. Combined with our proven bearing press design, the SBK-1 quickly and easily pushes the old bearing out of the linkage and reinstalls the new bearing precisely and squarely.
- Magnetic back plate for easy configuration and assembly
- Organized in a convenient storage case
Includes extractor cups/drifts for the following ODs:
- 16mm
- 17mm
- 19mm
- 20.6mm
- 21mm
- 22mm
- 22.3mm
- 24mm
- 26mm
- 28mm
- 28.6mm
- 30mm
- 32mm
- 35mm
Includes extractor studs and pilots for bearings with the following IDs:
- 8.5–9mm
- 10mm
- 12mm
- 12.7mm
- 15mm
- 17mm
- 20mm
NOTE: For bearing extraction, the SBK-1 requires a minimum of 3mm of flat linkage structure outside the bearing to support the extractor cup/drift. For bearings without this flat structure, consider using the Park Tool SHX-1 Slide Hammer Bearing Extractor.

$239.99
A perfect way to start a bicycle tool collection! A great combination of tools to help a home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-4 includes more than 15 genuine Park Tool products that can perform dozens of tasks and includes a custom Park Tool toolbox with extra room for spare parts and more tools.
The SK-4 includes:
- AWS-10 Fold-Up Hex Wrench Set
- BBB-4 Big Blue Book of Bicycle Repair
- CC-3.2 Chain Checker
- CN-10 Professional Cable and Housing Cutter
- CT-5 Mini ChainBrute Chain Tool
- FR-5.2 Cassette Lockring Tool
- GSC-1 GearClean Brush
- HCW-16.3 Chain Whip/Pedal Wrench
- HR-8 8mm Hex Wrench
- MLP-1.2 Master Link Pliers
- SD-2 Shop Screwdriver: #2 Phillips
- SW-7.2 Triple Spoke Wrench
- TL-1.2 Tire Lever Set
- TWS-3 Torx Compatible 3-Way Wrench

$232.14
The 2197 is an add-on accessory for the Park Tool DT-5 and DT-5.2 Disc Brake Mount Facing Set to enable easier and more efficient facing of disc brake mounts on carbon fiber frames. Features a brazed-on diamond grit surface that is over 100 times more durable and effective on carbon fiber than the cutter included with the DT-5.2. The 2197 sits between the cutter of the DT-5.2 and the brake mount, and smoothly and evenly grinds the mounting surface until it is flat and properly perpendicular to the rotor.
NOTE: The 2197 is intended for facing carbon fiber only. Aluminum, steel, and titanium disc brake mounts should be faced using the #2171 facing cutter included with the DT-5.2. For carbon frames that feature aluminum inserts (with a carbon/aluminum hybrid mounting surface), use the #2197. When machining carbon fiber, regularly apply water (or a similar solution) to the cutting surface.

$149.95
Designed and built specifically for a wide variety of bicycle hex work the THH-1 is a set of eight common sizes of professional quality T-Handle hex wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite hex set, the THH-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included).
- Carefully selected combination of Chrome Vanadium and S-2 tool steels
- 2, 2.5, 3, 4, 5, 6, 8 and 10mm hex wrenches included
- Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless
- Machined, chamfered tips allow easier insertion into hex fittings
- Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or over-sized hexes fast and easy
- Sliding T-handle creates increased leverage and multiple access positions
- Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

$135.95
The BKD-1 Hydraulic Brake Bleed Kit will bleed most models of DOT-fluid-based hydraulic brakes. Hydraulic systems need bleeding to remove any air bubbles and to inject new, clean fluid.
- Designed and built for home use and the rigors of daily commercial use
- Includes two syringes, hoses with shutoff clips, multi-size bleed blocks and a unique attachable syringe mount
- Housed in a rugged reusable case
- Machined stainless steel and 7075 aluminum fittings to service SRAM, Hayes, Formula, Hope and other brands of DOT-fluid-based hydraulic brake systems
- Replacement parts available
- Brake fluid not included

$127.95
An alignment gauge is essential for diagnosing and repairing bent or misaligned derailleur hangers, often the source of shifting problems. The DAG-3 features an all-new design, engineered and built to be light, accurate, and versatile. The sliding indicator can measure derailleur hanger alignment against bicycle rims of any size and rotates out of the way to clear seat stays, racks, and other obstacles, allowing 360-degree measurement. The long, precision-extruded aluminum body is built to exacting tolerances and provides ample leverage for making adjustments.
- Compatible with 16" to 29"+ wheels (ISO/ETRTO rim sizes from 317 to 630+)
- Replaceable M10 threaded tip
- Low-profile head fits low clearance thru-axle derailleur hangers and Shimano Direct Mount hangers
- Length: 16.5" (420mm)
- Weight: 22.75 oz. (645g)

$123.95
Designed and built specifically for a wide variety of bicycle Torx compatible work, the THT-1 is a set of eight common sizes of professional quality T-Handle star-shaped wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite Torx compatible set, the THT-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included).
- Carefully selected combination of Chrome Vanadium and S-2 tool steels
- T6, T8, T10, T15, T20, T25, T30 and T40 Torx compatible wrenches included
- Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless
- Sliding T-handle creates increased leverage and multiple access positions
- Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

$70.95
"Take the guesswork out of internal routing. The IR-1.3 speeds the installation of internally-routed cable, housing, electronic wiring and hydraulic hose into carbon fiber, titanium, and aluminum frames. The straightforward guide magnet system utilizes five long guide cables with unique fittings, which can be routed through the frame in a number of ways using the included guide magnet. Everything is neatly stored in a convenient compact case. A true time and frustration saver!??Includes five 188 cm (74"") guide cables with attached magnets and unique fittings:
• Barbed adapter — Threads into the end of brake & shift cable housing as well as hydraulic brake hose
• Rubber adapter — Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS
• Di2®-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® shift wire, and is perfectly sized to fit into frame holes as small as 6 mm
• Di2® EW-SD300-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® EW-SD300 shift wire
• Reverse-polarity magnet — Used in conjunction with any of the other guide cables - feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes
Also included:
• Double-threaded barb — Securely attaches new housing or hydraulic hose to existing housing or hose, allowing for easy replacement without redoing the routing
• Guide magnet — routes guide cables through the frame from the outside"

$59.95
The QTH-1 is an ergonomic T-handled bit driver equipped with eight common bits to fit a wide variety of fasteners and fittings found on bicycles. The magnetic "quick-change" handle allows for one-handed operation and makes changing bits quick and easy. The bit holder can be magnetically attached to any magnetic surface such as a repair stand or tool box, or can be permanently mounted to any wall or tool board. The QTH-1 is a professional-grade tool built to withstand the rigors of daily shop use and is fully rebuildable.
Includes the following magnetic 1/4" bits:
- 2mm, 2.5mm, 3mm, 4mm, 5mm & 6mm hex
- T25 Torx-compatible
- #2 Philips cross tip
- Bit holder includes empty spaces for 2 extra bits

$54.99
Park's Freewheel Remover Wrench provides superior leverage for freewheel removal and installation. Its head slides over Park freewheel removers and features a locking knob for a secure fit.

$54.95
Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles.
Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels.
* Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.

$49.99
The HBH-3 securely holds handlebars in place on any bike in any position while in a repair stand. It's useful for brake bleeding, cable and housing routing, lever adjustment, or any scenario where you want to prevent the handlebars from rotating, including storage or working with the bike rotated upwards. With its articulating clamps and adjustable straps, the HBH-3 can easily be attached in a wide variety of positions onto almost any handlebar, seatpost, frame, fork, or repair stand. Anodized aluminum construction with soft rubber straps.
- Straps install onto any round tube from 12mm to 60mm (0.5" to 2.4"), as well as most irregular and aero-shaped tubing found on bicycles
- Rotating articulating clamps allow for secure installation onto virtually any bicycle in a wide range of positions
- Usable extension length of 18" to 32" (45cm to 81cm)
- Collapses and folds to 17" (43cm) for storage

$46.99
Accurately gauge the straightness of disc brake rotors while the wheel is mounted in a TS-2.2 or TS-2 Professional Wheel Truing Stand (each sold separately). Park Tool's Rotor Truing Gauge features an infinitely adjustable, finely threaded indicator gauge. It works with any diameter brake rotor.

$46.95
Bottom brackets have some of the highest torque specs of any component found on a bicycle. Despite this, some bottom bracket cups feature tool fittings that allow mere millimeters of engagement, which can be a problem when attempting removal or installation. Solution: the Park Tool Bottom Bracket Tool Retaining System. Used in conjunction with nearly any Park Tool bottom bracket tool, the BBT-RS uses a spring-based tension system to apply consistent, adjustable pressure to the tool, ensuring full engagement with the tool fitting and preventing slippage.
The BBT-RS can be configured for use with the vast majority of threaded and thread-together bottom bracket standards. The BBT-RS features an M8 threaded rod and a double-sided adapter nut with M12 and M15 threads, allowing it to thread directly into any compatible cartridge bottom bracket. The M15 adapter can also be used to install any of Park Tool's nine aluminum bottom bracket tools, all of which feature integrated threading for use with the BBT-RS.
- Washer diameter: 57 mm (2.25")
- Rod length: 175 mm (6.9")
- Rod threading: M8 x 1.0
- Adapter nut threading: M12 x 1.0 & M15 x 1.0
Compatible with the following bottom bracket styles:
- Threaded cup
- Thread-together
- Cartridge
- Cup-and-cone
Compatible with the following bottom bracket tools:
- The following Park Tool socket-style aluminum bottom bracket tools:
- BBT-27.3
- BBT-35-12
- BBT-35-36
- BBT-47-12
- BBT-47-16
- BBT-49.3
- BBT-59.3
- BBT-69.3
- BBT-79.3
- Wrench-style bottom bracket tools with a handle (e.g. Park Tool BBT-9, BBT-29, HCW-4)
- Bottom bracket tools with external wrench flats (e.g. Park Tool BBT-19.2, BBT-22)

$42.95
An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-2.2 is intuitive and easy to use, and applies up to 60 Nm of torque to any fastener or component with left or right-handed threads. Perfect for mid-to-high-torque applications such as bottom brackets, cassette lockrings, and crank bolts. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet, as well as most threaded bottom bracket tools.
- 0 to 60 Newton meter (0 to 50 foot-pound) range
- 3/8" drive
- Reads and registers torque values for both left hand and right hand threading
- Length: 17.75" (450 mm)

$39.99
A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings.
The Chain Gang includes:
- CM-5.3 Cyclone Chain Scrubber
- GSC-1 GearClean Brush
- 8 oz. bottle of Bio ChainBrite
The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.

$39.95
An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-1.2 is intuitive and easy to use, and applies up to 14 Nm of torque to any fastener or component with left or right-handed threads. Perfect for low-torque applications such as stem bolts, levers, and carbon fiber components. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet.
- 0 to 14 Newton meter (0 to 140 inch-pound) range
- 3/8" drive
- Reads and registers torque values for both left hand and right hand threading
- Length: 11.5" (292 mm)

$37.99
Park's Professional Pedal Wrench features an angled, oversize head for maximum leverage. It has two 15mm wrenches at different angles, so you can maximize your leverage, and a long, round, vinyl-coated handle that won’t dig into your hand the way flat wrenches do. There's even a hole in the end for hanging the wrench on your toolboard.

$36.95
A puncture in your tubeless tire doesn't have to be a death sentence for your ride. This handy carry-along tool repairs small punctures and cuts in tubeless bicycle tires without removing the tire from the rim, getting you back on the trail in no time. The TPT-1 easily plugs the hole by inserting one of the 5 included vulcanized rubber plugs into the puncture. This shrinks the puncture down to a manageable size, allowing the tubeless sealant to do its job and reestablish a seal. The unique sliding plug retainer holds the plug in place and prevents it from being pulled back out as the tool is removed. Everything is stored in a compact package that fits easily in a saddlebag or backpack pocket.
- Includes 5 vulcanized rubber plugs (refills available — part #2370K)
- Dimensions: 89 x 27 x 40 mm (3.5" x 1.1" x 1.6")
- Weight: 79 grams (2.8 oz.) with plugs
NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.

$34.95
A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 16-notch tool fittings, including Wheels Mfg™ Thread Together & FSA® MegaEvo®. Manufactured in-house by Park Tool, anodized for easy identification, and featuring a ratchet/torque wrench-compatible 3/8" drive.
Fits 16-notch bottom bracket tool fittings with a major diameter of 48–50 mm and a minor diameter of 46.4 mm, including:
- FSA® MegaEvo®
- Wheels Mfg™ Thread Together
Note: Does not fit Hope™ BSA30

$33.95
The MTB-5 packs 16 functions into one slim, tough folding multi-tool, making it the ideal companion for any trailside adjustment or emergency fix. Features a full set of hex wrenches and screwdrivers, a T25 Torx-compatible driver, and five specialty tools to aid in common on-the-ride repairs.
Includes the following:
- 2, 2.5, 3, 4, 5, 6 & 8 mm hex wrenches
- T25 Torx-compatible driver
- Philips #2 cross tip & flat head screwdrivers
- Chain tool (5 to 12 speed compatible)*
- Spoke wrenches (equivalent to SW-0 and SW-2)
- Presta valve core removal tool
- Disc brake rotor truing tool
- Disc brake pad spreader
*The MTB-5 will not peen Campagnolo 11, 12 or 13 speed chain rivets
- Dimensions: 3.1" x 1.8" x 0.8" (79 x 45 x 20 mm)
- Weight: 6.9 oz. (195 g)
- Replaceable chain tool pin (Part #985-1)

$33.87
The BK-UK includes six new and revised parts for the Park Tool BKD-1 and BKM-1 Hydraulic Brake Bleed Kits, allowing for compatibility with the latest brake models from popular manufacturers.
Includes:
- Part #2600A (x2) — M4 x 0.8 adaptor for use with SRAM DB8, Trick Stuff, and Campagnolo mineral oil brake systems
- Part #2588.2 — Thin-walled hose compression sleeve for internal bleed nipples, such as those found on Shimano mineral oil brake systems
- Part #2574A — Hose assembly with integrated fitting for bleed nipples such as those found on Shimano mineral oil brake systems
- Part #2615-2 (x2) — 11 mm bleed blocks for use with Hayes DOT brake systems
All parts also available individually.
NOTE: The seals on each part are designed for one type of fluid — DOT fluid or mineral oil — and should be used only on the systems they were intended for. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure.

$32.95
The HCW-16.3 is a combination 15mm pedal wrench and chain whip. Use for both pedal removal/installation and for cassette removal. Chain whip features improved compatibility with 5-speed to 12-speed mountain and road bike cassettes and freewheels. The HCW-16.3 is 10.75" long (27.3cm).

$31.95
A great way to keep the benchtop organized during a repair, the OM-2 features an over-sized textured work area and raised trays for organizing small parts and hardware. Perfect for overhauling or rebuilding components such as forks, shocks, hubs, suspension linkages, derailleurs, etc.
- Measures 15 x 24.5-inches (38cm x 62cm)
- Interlocking edges allow multiple mats to be joined together
- Tear/abrasion/shock-resistant TPR construction

$15.95 - $31.95
Professional quality T-Handle hex wrench built for speed, efficiency, leverage and a perfect fit.
- Carefully selected combination of Chrome Vanadium and S-2 tool steels
- Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless
- Machined, chamfered tips allow easier insertion into hex fittings
- Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or oversized hexes fast and easy
- Sliding T-handle creates increased leverage and multiple access positions

$30.95
A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 12-notch tool fittings, including SRAM BSA DUB, Race Face Cinch, Rotor BSA30, and others. Manufactured in-house by Park Tool, anodized for easy identification and featuring a ratchet/torque wrench-compatible 3/8" drive.
The BBT-79.3 features integrated threads for full compatibility with the Park Tool BBT-RS Bottom Bracket Tool Retaining System (sold separately). The BBT-RS uses an adjustable spring-based tension system to apply consistent, adjustable pressure to the tool, ensuring full engagement with the tool fitting and preventing slippage.
Fits 12-notch threaded bottom bracket tool fittings with a major diameter (outside of notches) of 45–47 mm and a minor diameter (inside of notches) of 44 mm, including:
- SRAM BSA DUB
- Race Face Cinch
- Rotor BSA30
- Zipp Vuma
- Hawk Racing BB3086
- and more
- 3/8" drive fitting

$29.99
A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 12-notch tool fittings, including Chris King ThreadFit T47 & ThreadFit 30 bottom brackets. Manufactured in-house by Park Tool, anodized for easy identification and featuring a ratchet/torque wrench-compatible 3/8" drive.
Fits 12-notch bottom bracket tool fittings with a major diameter of 50–53 mm and a minor diameter of 48.2 mm, including:
- BBInfinite T47
- Chris King ThreadFit T47
- Chris King ThreadFit 30
- Enduro BBRight Torqtite
- Hambini T47
- Rotor T47 External 30mm
- Rotor BBright, BB30, BB386EVO, and PF30 thread-together
Page 1 of 3
Next page