Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.
A compact, efficient way to hold flat fixing essentials so you can get back on the bike quickly. The Pro Flat Pack has everything you need to fix a flat and get back on the bike quickly in an aero, easy to grab package. This all-in-one kit provides essential items needed to fix a flat tire with additional pockets for money and ID, plus extra soft, padded materials to ensure you won't be bothered by the poke of a tool while it's stashed in your back pocket. - Tight fitting, stretch neoprene material zips open for easy access - All the items you need to fix a flat tire - Includes Air Rush Elite, CO2‚ inflator, two 16g CO2‚ cartridges, and a padded bag - Reusable hand insulation sleeve, vulcanizing patch kit - Room in the bag for ID, money, keys, and more
A compact yet capable tool with an array of hex, torx, spoke, screwdriver, and chain tools. Make road- or trail-side adjustments and fixes with confidence using 1 of 15 integrated tools packaged in the slim and easy-to-carry design of Bontrager Pro Multi-Tool. A vast array of hex, torx, spoke tools and screwdrivers will have you back on your back in no time —and it all packs down small in a magnetic case for easy carrying in a pocket or bag. Product details - Slim magnetic case doubles as handle for all tools, including chain tool - 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm, #2 Phillips, #1 Flat, T25 and 0, 1, 2, 3 spoke - Lightweight, durable design stows nearly anywhere - Chain tool compatible with 8, 9, 10, 11, 12-speed drivetrains - Integrated bottle opener for post ride refreshments
- Lightweight and low profile - Forged center-pivot stainless steel bits - Durable stainless steel fastening hardware - CNC 7075 alloy side plates - Hex 2/3/4/5/6mm - T10/T25 - Phillips - Chain breaker tool (includes hex 8/10mm wrench, 4 spoke wrenches) - Tubeless tire plug kit - 122g
The HBH-3 securely holds handlebars in place on any bike in any position while in a repair stand. It's useful for brake bleeding, cable and housing routing, lever adjustment, or any scenario where you want to prevent the handlebars from rotating, including storage or working with the bike rotated upwards. With its articulating clamps and adjustable straps, the HBH-3 can easily be attached in a wide variety of positions onto almost any handlebar, seatpost, frame, fork, or repair stand. Anodized aluminum construction with soft rubber straps. - Straps install onto any round tube from 12mm to 60mm (0.5" to 2.4"), as well as most irregular and aero-shaped tubing found on bicycles - Rotating articulating clamps allow for secure installation onto virtually any bicycle in a wide range of positions - Usable extension length of 18" to 32" (45cm to 81cm) - Collapses and folds to 17" (43cm) for storage
- Hex wrenches 2, 2.5, 3, 4, 5, 6, 8 - TX wrenches 10, 25 - PH1 screwdriver - Chain tool - Schrader & Presta valve tool - Flat screwdriver 1.0 x 5.0 - Spoke Key 3.3, 3.45 and DT
Fix tubeless tire punctures and broken chains. This multi-tool has a chain tool on one end and a tire plug built into the handle, with inner storage for tubeless tire plugs. The full multi-tool was designed for use with an EnCase System Storage Sleeve, which fits inside bar ends of your handlebars. Ride with this multi-tool in a storage sleeve or in a tool wrap for easy repairs while riding. - Compatible with all bicycle chains, including 12-speed - Inserter tool and bacon strips plug holes in tubeless tires - Five bacon strip tire plugs included; refills available - Hardened steel chain pin driver for lifetime durability - Store in handlebar with a Wolf Tooth EnCase Storage Sleeve (sold separately) or carry in a jersey pocket - Chain tool driver requires 4mm hex (available on EnCase System Hex Bit Wrench) - Fits most standard mountain handlebars and most drop bars (except ergonomic drop bars that have hard angles in the drops)
Make simple trailside or roadside repairs with this multi-tool that has 14 functions. An 8mm hex head has a 4mm insert to fit each of the eight attached hex bits. With its slim design, this multi-tool can be stowed inside an EnCase System Storage Sleeve to be carried in handlebar ends as it was designed, or a mainstay on any home workbench. - 14 functions (spoke wrench; valve core wrench; flat head #3.5; Phillips #2; 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, and 8mm hex; and T10, T25, and T30 Torx) - Magnets & O-rings keep all parts in place - Ball detent swivel head helps access hard-to-reach places - Handle doubles as breaker bar when ball detent swivel head is bent for extra torque - Store in handlebar with a Wolf Tooth EnCase Storage Sleeve (sold separately) - Magnet on bottom end of tool allows for storage on steel bike stands - Fits all standard mountain handlebars and most drop bars (except being ergonomic drop bars that have hard angles in the drops)
The Tool Wrap was designed to make trailside repairs quick and efficient. Featuring multiple flaps that allow you hang it from a wall, act as a changing area foot pad and more, the Tool Wrap is the perfect trailhead companion. - Top flap that can be shut in a car door for a mobile workshop - Bottom flap provides a work space to keep your parts and tools out of the dirt when working on the ground - Pocket layout is ideal for all the tools you need to build a bike - Aluminum eyelets for hanging up in your home or work shop - Dimensions: 68 by 46 cm (main body), 60 by 20 cm top flap (for car door), 32 by 60 cm bottom flap (work space), rolled up diameter size varies
Accurately gauge the straightness of disc brake rotors while the wheel is mounted in a TS-2.2 or TS-2 Professional Wheel Truing Stand (each sold separately). Park Tool's Rotor Truing Gauge features an infinitely adjustable, finely threaded indicator gauge. It works with any diameter brake rotor.
- 3/32" chain whip
Bottom brackets have some of the highest torque specs of any component found on a bicycle. Despite this, some bottom bracket cups feature tool fittings that allow mere millimeters of engagement, which can be a problem when attempting removal or installation. Solution: the Park Tool Bottom Bracket Tool Retaining System. Used in conjunction with nearly any Park Tool bottom bracket tool, the BBT-RS uses a spring-based tension system to apply consistent, adjustable pressure to the tool, ensuring full engagement with the tool fitting and preventing slippage. The BBT-RS can be configured for use with the vast majority of threaded and thread-together bottom bracket standards. The BBT-RS features an M8 threaded rod and a double-sided adapter nut with M12 and M15 threads, allowing it to thread directly into any compatible cartridge bottom bracket. The M15 adapter can also be used to install any of Park Tool's nine aluminum bottom bracket tools, all of which feature integrated threading for use with the BBT-RS. - Washer diameter: 57 mm (2.25") - Rod length: 175 mm (6.9") - Rod threading: M8 x 1.0 - Adapter nut threading: M12 x 1.0 & M15 x 1.0 Compatible with the following bottom bracket styles: - Threaded cup - Thread-together - Cartridge - Cup-and-cone Compatible with the following bottom bracket tools: - The following Park Tool socket-style aluminum bottom bracket tools: - BBT-27.3 - BBT-35-12 - BBT-35-36 - BBT-47-12 - BBT-47-16 - BBT-49.3 - BBT-59.3 - BBT-69.3 - BBT-79.3 - Wrench-style bottom bracket tools with a handle (e.g. Park Tool BBT-9, BBT-29, HCW-4) - Bottom bracket tools with external wrench flats (e.g. Park Tool BBT-19.2, BBT-22)
Headset cup installation adapters allow for precise installation of Cane Creek headsets and prevent damage to both the cups and press. - Precision engineered in Fletcher, NC - One side can be used with cups featuring non-removable bearings (pressure is applied precisely on the outer race, preserving the integrity of the bearing itself), while the other is used for cups featuring removable bearings (pressure is applied to the cup race via a chamfered surface, reducing the risk of slippage) - Hard anodized AL7075 to reduce wear - Intended to be used in concert with a headset press tool to install any press-fit headset configuration
- Lightweight and low profile - Forged center-pivot stainless steel bits - Durable stainless steel fastening hardware - Hex 2/3/4/5/6/8mm - T10/T25, Phillips - Lightweight AL chain breaker tool - 102g
Precision brake bleeding tools and adaptor kits for Magura brake systems. - Consumer level bleed kit
- Hex wrenches 2, 2.5, 3, 4, 5, 6, 8 - TX wrenches 10, 25 - PH1 screwdriver - Chain tool - Schrader & Presta valve tool
This ultralight hex and bottom bracket wrench has a 1-inch hex at one end and an external BB cup spline at the other end. The 1-inch hex end features magnets that quickly couple with Wolf Tooth's steel hex insert tools. - 1-inch hex drive at one end and 16-notch 44mm bottom bracket tool (or centerlock rotor tool) at the other end - Includes the wrench only. Steel inserts are not included but can be purchased separately - 1-inch hex drive interface compatible. Magnets inset allow quick coupling and decoupling of steel inserts
- Brake holder features M5, M6 & passthrough holes for attaching all disc brake mounting styles as well as most rim brake caliper styles - 1-1/8" steerer tube features star nut for retaining top cap and spacers - 2" flared cone for compatibility with tapered steerer tubes - Compatible with 1-1/8" threadless stems only—not compatible with threaded headset/quill stem setups
An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-2.2 is intuitive and easy to use, and applies up to 60 Nm of torque to any fastener or component with left or right-handed threads. Perfect for mid-to-high-torque applications such as bottom brackets, cassette lockrings, and crank bolts. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet, as well as most threaded bottom bracket tools. - 0 to 60 Newton meter (0 to 50 foot-pound) range - 3/8" drive - Reads and registers torque values for both left hand and right hand threading - Length: 17.75" (450 mm)
The ultimate trailside companion. These high tensile steel multi-tools feature a precise fit and finish and side grips for a secure handhold even with gloves on. The m19 includes: - Chain tool: 8/9/10 speed compatible - Spoke wrench: #0, 1, 2, 3 - Hex wrenches: #2, 2.5, 3, 4, 5, 6, 8 - Open wrench: 8mm, 10mm - Screwdrivers: Phillips #1, Phillips #2, flat #2 - Torx: t-10, t-25 - Stainless steel carrying case - Length: 89 mm - Weight: 175g - Warranty: lifetime
Professional-grade, versatile bike chain multi-tool engineered for a variety of road or trailside repairs. The Multi Chain Pliers are constructed from machined aluminum and feature an integrated quick-link tool, chain breaker, valve core tool, bottle opener, rotor aligner, and magnetic holders for up to two spare quick links. Its slim design allows for maximum portability and it's engineered for long-lasting use. It also features an anodized finish and a hardened steel chain breaker pin. Mountain bikers, road cyclists, and gravel grinders will all find its versatility highly useful, whether in the workshop or out on the road or trail. - Weight: 61g - Dimensions: 120 x 38 x 10mm
Durable and compact chrome-plated ratchet tool designed for bicycles. Fine-tooth ratchet with reversing lever and a fixed opening on opposite end. Tool selection optimized for road, gravel and mountain bikes. Super-hard CRV (chrome vanadium) bits. Custom, machined aluminum extension adapter with laser-etched logo. Integrated magnet holds tool bits in place. Ratchet Kit comes in a compact, soft shell carrying case. - Weight: 140g Tool Bits: - Hex 2, 2.5, 3, 4, 5, 6, 8mm - Star Shaped T10, T25, T30 - Flat Head - Phillips-Head
- Heavy-duty device that cleans chain in seconds - The kit includes a 75 ml bottle of Drivetrain Cleaner that can be either sprayed over the drivetrain or poured into the top reservoir - Liquid release button ensures the application of the cleaner is quick and easily controlled. - Abrasive cleaning teeth and rotating brush wheels which have 120 contact points cover every part of each chain link for a deep and thorough clean - Excess dirty fluid drops into a second lower reservoir so it’s kept away from the clean chain
An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-1.2 is intuitive and easy to use, and applies up to 14 Nm of torque to any fastener or component with left or right-handed threads. Perfect for low-torque applications such as stem bolts, levers, and carbon fiber components. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet. - 0 to 14 Newton meter (0 to 140 inch-pound) range - 3/8" drive - Reads and registers torque values for both left hand and right hand threading - Length: 11.5" (292 mm)
Material: premium plus carbon steel, drop forged, entirely hardened and tempered, cutting edges induction hardened
Park's Professional Pedal Wrench features an angled, oversize head for maximum leverage. It has two 15mm wrenches at different angles, so you can maximize your leverage, and a long, round, vinyl-coated handle that won’t dig into your hand the way flat wrenches do. There's even a hole in the end for hanging the wrench on your toolboard.
A compact multi-tool that is designed for integrated storage in compatible Trek road frames. Compact and easily stowed The BITS Integrated Multi-Tool is a compact multi-tool that is designed for clean, integrated storage into compatible Trek road bike frames. The small but smart design features hex tools from 2-8mm along with a T25 Torx, and flathead screwdriver. The ergonomic design makes the tool as easy to use as it is to carry. Product details - Designed for secure integrated storage in the new Domane with storage door - CNC-machined keys for lightweight durability - 2, 2.5, 3, 4, 5, 6, and 8mm hex along with T25 and flat-head screwdriver - Slim profile makes it easy to pack on any ride - Ultralight aluminum alloy design
Material: premium plus carbon steel, drop forged, entirely hardened and tempered, cutting edges induction hardened
- Also for clenching and separating of from cables and other sensitive objects - Serrated gripping surface - Cutting edges induction hardened
A puncture in your tubeless tire doesn't have to be a death sentence for your ride. This handy carry-along tool repairs small punctures and cuts in tubeless bicycle tires without removing the tire from the rim, getting you back on the trail in no time. The TPT-1 easily plugs the hole by inserting one of the 5 included vulcanized rubber plugs into the puncture. This shrinks the puncture down to a manageable size, allowing the tubeless sealant to do its job and reestablish a seal. The unique sliding plug retainer holds the plug in place and prevents it from being pulled back out as the tool is removed. Everything is stored in a compact package that fits easily in a saddlebag or backpack pocket. - Includes 5 vulcanized rubber plugs (refills available — part #2370K) - Dimensions: 89 x 27 x 40 mm (3.5" x 1.1" x 1.6") - Weight: 79 grams (2.8 oz.) with plugs NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.